Buy resin chemicals | polymer chemicals | resin chemical manufacturers | resins chemicals suppliers - Worldofchemicals

chemical-categories

TCC-ID.288-AC

TCC-ID.288-AC densified matrix resin is a rigid, NPG-isophthaic, unsaturated polyester resin. It is used to make non-gel coated parts with U.V. and stain resistance.

Properties Suppliers
TCC-lB-634-NE

TCC-lB-634-NE is spray dried, freeflowing melamine-formaldehyde resin powder.Suitable for the production of moulding compounds for food trays, dishes, parts for electrical appliances and tools, and other molded products.

Properties Suppliers
Trimesic Acid

Trimesic Acid is a kind of important chemical raw material. It is used for producing such as plastic, man-madefibre, water soluble alkyl resin, plasticizer, medicament intermediate etc.

Properties Suppliers
UROTUF L51-35

UROTUF L51-35 is a fully reacted, color-retentive, thermoplastic urethane dispersed in a blend of water and N methylpyrrolidone. UROTUF® L51-35 is a higher solids version of UROTUF® L51, which allows for greater formulating latitude.

Properties Suppliers
Valeraldehyde

Valeraldehyde is an alkyl aldehyde. It is used in flavorings, resin chemistry, and rubber accelerators.

Properties Suppliers
Vydyne 20NSP1

Vydyne 20NSP1 is a general-purpose, highly nucleated nylon 6,6 resin with internal and external lubricant. It is designed to crystallize rapidly when cooled from the molten state. This rapid crystallization can result in reduced cycle times and increased productivity through faster part setup when compared with standard general purpose nylon 6,6 resins. The crystalline structure resulting from nucleation will alter part properties, yielding increased modulus or rigidity, increased tensile strength, reduced elongation, reduced impact strength and mold shrinkage compared with standard general-purpose nylon 6,6.The Vydyne 20NSP series resins have an internal lubricant for improved machine feed and mold release. This formulation is designed to provide easy release of parts from molds using standard molding conditions. The rapid crystallization of Vydyne 20NSP resins may allow part ejection at higher temperatures compared with general-purpose nylon 6,6. This will reduce the mold closed time and thereby decrease the molding cycle. Critical factors unique to each application such as mold/part design, tolerances, etc., may negate these cycle time benefits. It is recommended to check critical part dimensions against specifications before implementing shorter molding cycles on a routine basis.Typical end uses for Vydyne 20NSP1 are terminal blocks, bearings, business control cams, electrical connectors, housings, wire ties, fasteners, switch components, and general industrial parts that require stiffness and rigidity.

Properties Suppliers
Vydyne 21SPC1

Vydyne 21SPC1 is a general purpose nylon 6,6 resin available in natural color. It is designed principally for injection molding fabrication. This resin offers a well balanced combination of engineering properties characterized by high strength, rigidity, good toughness, high melt point, good surface lubricity, abrasion resistance and resistance to many chemicals, solvents, gasoline and machine and motor oils. Vydyne 21SPC1 permits production of molded parts with good initial color plus good property and color retention when using regrinds. This resin is recognized by Underwriters Laboratories and conforms to the requirements of many industrial, federal, and military specifications for premium quality general purpose nylon 6,6 resins.Vydyne 21SPC1 is intended for use in high productivity applications. In many applications, the molding cycle can be reduced because parts may be removed from the cavity at higher temperatures.

Properties Suppliers
Vydyne 21SPF1

Vydyne 21SPF1 is a general purpose nylon 6,6 resin. It is designed principally for injection molding fabrication. This grades offer a well-balanced combination of engineering properties characterized by high strength; rigidity; good toughness; high melt point; good surface lubricity; abrasion resistance; and resistance to many chemicals, solvents, gasoline and machine and motor oils. Vydyne 21SPF series resins permit production of molded parts with good initial color plus good property and color retention when using regrind. This resin is recognized by Underwriters Laboratories and conforms to the requirements of many industrial, federal and military specifications for premium-quality, general purpose nylon 6,6 resins. Vydyne 21SPF series resins are internally and externally lubricated for improved machine feed and exceptional mold release. They are intended for use in high-productivity applications. In many applications, the molding cycle can be reduced because parts may be removed from the cavity at higher temperatures. In difficult molds where parts have a tendency to stick in the cavity, Vydyne 21SPF can reduce or eliminate the need for mold release sprays. Critical molded part dimensions should be checked against specifications before implementing shorter molding cycles on a routine production basis.

Properties Suppliers
Vydyne 52BWMS

Vydyne 52BWMS is a medium-viscosity resin used for extrusion- compounding. It is the product of choice for low-yellowness-required applications. This product with its higher viscosity is a part of the 50BW/50BWFS series. It provides melt stability during the compounding step to maintain its flow. Resistance of Vydyne 52BWMS to heat, oil and wear is typical of PA66 neat resins.

Properties Suppliers
Vydyne ECO315

Vydyne ECO315 is a non-halogenated, noncorrosive injection molding grade nylon with ignition resistant additives. It is lubricated to facilitate machine feed and mold release. Vydyne ECO315 is modified with ignition resistant additives to help users meet Underwriters Laboratories flammability rating requirements for molded parts requiring (UL) 94 V-0 classification at thicknesses down to 0.032 inches.Vydyne ECO315 has a comparatively low specific gravity for an ignition resistant resin. Meaningful economic comparisons of molding materials must be based on cost per cubic inch, which is reduced by lowered specific gravity.

Properties

www.worldofchemicals.com uses cookies to ensure that we give you the best experience on our website. By using this site, you agree to our Privacy Policy and our Terms of Use. X