Towards efficiency in thermoelectric nanowires

Towards efficiency in thermoelectric nanowires

4:49 AM, 4th February 2015
Towards efficiency in thermoelectric nanowires
Graham Yelton and Sandia National Laboratories colleagues have developed a single electroforming technique that tailored key factors to better thermoelectric performance: crystal orientation, crystal size and alloy uniformity.

ALBUQUERQUE, NEW MEXICO: Efficiency is big in the tiny world of thermoelectric nanowires. Researchers at Sandia National Laboratories say better materials and manufacturing techniques for the nanowires could allow carmakers to harvest power from the heat wasted by exhaust systems or lead to more efficient devices to cool computer chips.

Sandia researchers published a paper, “Using Galvanostatic Electroforming of Bi1-xSbx Nanowires to Control Composition, Crystallinity and Orientation,” in edition of the Materials Research Society’s MRS Bulletin. The authors are W Graham Yelton, Steven J Limmer, Douglas L Medlin, Michael P Siegal, Michelle Hekmaty, Jessica L Lensch-Falk, Kristopher Erickson and Jamin Pillars.

The work was the first time researchers managed to control crystal orientation, crystal size and alloy uniformity by a single process. All three factors contribute to better thermoelectric performance, said Yelton.

“The three together mean a huge gain, and it’s hard to do. It’s turning the knobs of the process to get these things to behave,” added Yelton.

Better nanowire geometries can reduce heat conductivity and improve what’s called the thermoelectric figure of merit, a measure of a material’s electrical and thermal conductivity. The higher the electrical conductivity and the lower the thermal conductivity, the higher the figure of merit and, therefore, the more efficient the material. However, the quality of previous thermoelectric nanowires proved inadequate.

Despite their inefficiency, some thermoelectric materials are already in use. Yelton compares their stage of development to the early days of solar photovoltaic cells: Everyone saw the potential, but they were so inefficient they were used only when nothing else worked.

Improved efficiency in nanowires would increase the use of thermoelectric materials. They’re already used in some sensors, and vehicle manufacturers hope they can harvest heat from exhaust systems to power vehicle sensor systems, said Yelton. Decreasing the power needed to run a vehicle’s operating system could reduce battery and alternator weight and perhaps eliminate some power-generating equipment, trimming vehicle size and weight.

Sandia’s paper described how the team created thermoelectric nanowire arrays with uniform composition along the length of the nanowire and across the spread of the nanowire array, which potentially can include hundreds of millions of nanowires. In addition, they created nanowire crystals of uniform size and orientation, or direction. Uniform composition improves efficiency, while orientation is important so electrons, the carriers of energy, flow better.

The team used a cost-effective method called room-temperature electroforming, which is widespread in commercial electroplating. Electroforming deposits the material at a constant rate, which in turn allows nanowires to grow at a steady rate. The method produced wires 70-75 nanometers in diameter and many microns long.

Yelton used pulses of controlled current to deposit the thermoelectric material, thereby controlling composition throughout the wire and the array. “There are little nuances in the technique that I do to allow the orientation, the crystal growth and the composition to be maintained within a fairly tight range,” he added.

The method produced a fairly large, slightly twisted crystalline wire structure that was almost a single crystal and had the desired orientation. “Without that, you couldn’t get good efficiencies,” said Yelton.

The chemistry of the material also is important. For the Sandia team, antimony salts play a major role in crystalline quality and orientation. Bismuth-antimony (Bi-Sb) alloys have some of the highest thermoelectric performance — acting both as a conductor of electricity and an insulator against heat — among many materials for near-room temperature applications. But existing Bi-Sb materials don’t produce effective solid-state cooling when power is constantly delivered to the device being cooled, such as a computer.

The Sandia team wanted a compound that behaved like a metal but would not conduct heat. Alloying antimony with bismuth fit the bill, said Yelton. Bi-Sb nanowire arrays electroformed with an antimony-iodide-based chemistry lacked the needed qualities, but arrays electroformed from an antimony-chloride-based chemistry produced crystallography and orientation for maximum thermoelectric performance.

“The chemistry allowed us to go from poly nano-crystalline structure to near single crystals of 2-5 micrometers,” giving better control over uniformity, said Yelton.

The next step is more challenging: making an electrical contact and studying the resulting thermoelectric behavior.

“Thermoelectric materials readily form oxides or intermetallics, leading to poor contact connections or higher electrical contact resistance. That reduces the gains achieved in developing the materials,” said Yelton.

While the Sandia team has been able to get good contact at the bottom of an array, making a connection at the top has proved difficult, he said. “To make a contact and measure array performance is not trivial,” said Yelton.

He and his colleagues are seeking further funding to solve the problem of successfully making contacts, and then to characterize the thermal electric properties of arrays. “If successful at the labs, we would try to find an industry collaborator to mature the idea,” he said.


© Sandia Labs News 



Your Comments (Up to 2000 characters)
Please respect our community and the integrity of its participants. WOC reserves the right to moderate and approve your comment.

Related News

Arkema completes acquisition of Bostik

COLOMBES, FRANCE: Arkema finalized the acquisition of Bostik, the world’s no. 3 in adhesives. With this acquisition, the Group reaches a new mil ...

Read more
Sumitomo to acquire compound semiconductor materials business of Hitachi Metals

TOKYO, JAPAN: Sumitomo Chemical has agreed to acquire compound semiconductor materials business of Hitachi Metals, Ltd. The acquisition is due to take ...

Read more
Air Liquide to invest €60 million in air separation unit in Australia

PARIS, FRANCE: Air Liquide announced a new long-term agreement in Australia with Nyrstar, an integrated mining and metals company. Air Liquide will in ...

Read more
Cheaper, cleaner method for bioethanol production using nitrogen gas

BLOOMINGTON, US: Indiana University biologists believe they have found a faster, cheaper and cleaner way to increase bioethanol production by using ni ...

Read more
New sticky labels to check self-cleaning glass

BELFAST, NORTHERN IRELAND: Reusable colour-changing sticky labels that act as a cheap and easy way to check the activity of photocatalysis-based self- ...

Read more
H.B. Fuller to acquire engineering adhesives provider, Tonsan

ST PAUL, US: H.B. Fuller Company has finalized the previously announced purchase of Tonsan Adhesive, Inc, the largest independent engineering adhesive ...

Read more uses cookies to ensure that we give you the best experience on our website. By using this site, you agree to our Privacy Policy and our Terms of Use. X